Film capacitor series keeps its cool even at 150°C
High-temp film capacitor, stays cool up to 150°C.
The Exxelia Dearborn 880P series of metalised Polyphenylene Sulfide (PPS) Film Capacitors is designed to keep cool when things get hot. With an operating temperature range of -55 to +150°C, they experience no derating for DC operations and none in AC operations up to +125°C.
This enables them to function at full capacity in extreme heat applications. The ability to operate at such high temperatures can eliminate the need for a cooling system within the design, thus reducing overall design time, weight and space.
PPS is a high-temperature, low-loss dielectric film used in the 880P series of wrap-and-fill capacitors. This allows them to feature superior electrical characteristics over an extremely wide temperature range and maintain excellent capacitance stability in one rugged, lightweight package. It performs consistently well in commercial applications such as in power supplies and in more demanding applications, such as in avionics, on a congested control or instrumentation panel.
The series features a capacitance range of 0.0047 to 10.0µF and voltage ratings from 50 to 400VDC with precision tolerances as low as ±¼% through ±10% yielding greater accuracy of capacitance. It is also a customisable unit with voltage maximums of 700 – 800VDC at 125°C maximum (higher voltages are available at reduced capacitance).
Made in the USA, the units are highly durable and capable of withstanding a five-pound pull force on lead axis. They are non-polar and demonstrate low loss factor, good voltage breakdown strength and high insulation resistance (low leak current) – and are completely stable over normal temperatures, voltages and frequency ranges. These characteristics allow the 880P series capacitors to deliver high performance in a variety of applications such as DC timing circuits, low- to high-frequency AC applications, and pulse or energy discharge uses.
Additionally, the package has axial leads with moisture-resistant, flame-retardant epoxy end seals and an outer tape covering for maximum performance.
ESA QPL Film capacitors
PM907S and PM948S are full series of Polyester Film Capacitors. PM907S products are suitable for voltages from 50V up to 1250V and offer capacitance values from 82nF up to 180μF. PM948S can be used with a voltages from 50V up to 630V with capacitance values from 22nF up to 47μF. Both series can support extreme conditions with temperatures from -55°C to +125°C, and offer high energy density, low ESR & ESL and high RMS current. Typical characteristics Self-healing properties Open circuit failure mode High reliability & quality High energy density Very light masse Low ESR & ESL
HIGH VOLTAGE CERAMIC CAPACITORS BASED ON BRAND NEW DIELECTRIC MATERIAL
No more compromises between stability and capacitance! The brand new C48X material combines most advantages of NPO and X7R dielectrics, enabling the new high power and high frequency ceramic capacitor range to provide great stability in voltage, high capacitance, great dissipation factor and fast charge/discharge. Miniaturization is a driving need for future electronics pieces of equipment. This evolution, true whatever the application, leads Exxelia Technologies (ex-Eurofarad) to develop a brand new high voltage ceramic capacitors range based on a new dielectric material named C48X, combining most of the advantages of NPO and X7R dielectrics. Compared to X7R material, C48X dielectric allows to get the same capacitance values under working voltage with the unrivaled advantage of a very low dissipation factor (less than 5.10-4). Besides, it can also withstand very high dV/dt, up to 10kV/μs, which makes it the solution of choice for pulse and fast charge/discharge applications. Thus capacitors with C48X dielectric appear to be ideally suited for power applications where heat dissipation may be detrimental to performances and reliability. Exxelia Technologies’ capacitors based on the C48X material have been developed from 200V to 5kV with chip sizes ranging from 1812 to 16080, allowing a maximum capacitance value of 10μF 200V (10 times more than with an NPO ceramic). The standard stacked versions are proposed with a maximum capacitance value of 47μF 200V. Regarding the mounting of these capacitors, many configurations are possible to be compatible either with surface mounting or through-hole mounting. All these versions can be suitable for space use and can be designed in order to avoid any whisker growth risk (10% min lead in all tin-lead alloys used). The introduction of the C48X range in the EPPL (European Space Agency Preferred Parts List) for space is in progress for sizes 0603 to 6560 from 100V to 1kV up to size 1210 and up to 5kV until the size 6560).