Introduction of DSCC 93026 qualified Wet Tantalum Capacitors
Exxelia has received the qualification by the Defense Supply Center Columbus (DSCC) as an approved provider of WT84 wet tantalum capacitors under the drawing DSCC 93026.
Exxelia’s range of wet tantalum capacitors WT84 is now fully qualified to DSCC 93026 drawing for voltages from 25V up to 125V. Available in all case sizes (T1, T2, T3, T4) the family is housed in a hermetically sealed tantalum case and is designed to withstand the most stringent environmental constraints. Thanks to the continuous improvements conducted in the manufacturing processes combined with the high purity tantalum powder used by Exxelia, DSCC 93026 provides the highest capacitance per unit volume. In addition, compared to conventional wet tantalum capacitors, DSCC 93026 features much lower ESR and higher ripple current.
DSCC 93026 is qualified for capacitance values range from 10µF up to 1800µF at voltages from 25V up to 125V, and with operating temperatures of -55°C to 125°C. The series is ideal for use in high-reliability defense, avionics, radars and power supply applications requiring high capacitance or high energy storage.
DSCC 93026 is available now for order.
Innovative new products at Electronica - Booth# B5 312 -
Felsic HV, long lifetime and high voltage screw terminal The Felsic HV family of aluminum electrolytic screw terminal capacitors provides great performances in energy density and ultra-long lifetime. For example products can withstand 8 000 hours at 105°C under high values of current which makes them the perfect choice to overcome railway constraints. The family also has one of the lowest ESR for aluminum capacitors, less than 10m0hms in most cases. Products are available for voltages from 160 to 450 Vdc, and offer capacitance values from 1500μF up to 47 000μF. Thus the family is a good compromise between reliability and compacity, with for example 47 000μF @ 160V in a 90x200mm volume. Cost-effective common-mode chokes qualified for aerospace Designed and qualified for aerospace, the TCM series is available in a through-hole package for horizontal and vertical mounting. TCM common-mode chokes are offered with inductances from 0.7 to 47mH under rated currents from 0.3A to 4A, and thoroughly tested by a dielectric withstanding strength at 1500VAC. Their excellent thermal properties allow the TCMs to operate without a hitch from -55°C up to +125°C, which, combined to the high mechanical resistance of the chosen materials (all meeting to UL94 V0 rating) make those products the perfect fit for aviation, defense and transportation industries. Ceramic capacitors based on the new C48X dielectric New range of high voltage ceramic capacitors based on brand new dielectric material C48X, combining most advantages of NPO and X7R dielectrics. Compared to X7R material, C48X dielectric allows to get the same capacitance values under working voltage with the unrivaled advantage of a very low dissipation factor (less than 5.10-4). Besides, it can also withstand very high dV/dt, up to 10kV/μs, which makes it the solution of choice for pulse and fast charge/discharge applications or firing units. Thus capacitors with C48X dielectric appear to be ideally suited for power applications where heat dissipation may be detrimental to performances and reliability. Ultra low ESR, high RF power and high self-resonant frequency The new NHB series is a complete range of MLCC based on NPO dielectric material providing a very high Self Resonant Frequency and limiting the parasite Parallel Resonant Frequencies. The series is available in 1111 size with capacitance ranging from 0.3pF to 100pF. NHB series offers excellent performance for RF power applications at high temperature up to 175°C and at 500 VDC. The lowest ESR is obtained by combining highly conductive metal electrodes and proprietary of new NPO low loss rugged dielectrics. NHB series particularly fits for high power and high frequency applications such as: cellular base station equipment, broadband wireless service, point to point / multipoint radios and broadcasting equipment.
New entity, Exxelia Magnetics
This is an internal merger of two innovative, professional and complementary companies both designer and manufacturer of high-end would magnetic components, which have a history of successfully working together for a year. Exxelia Magnetics will have greater scale, breadth and capabilities to compete more effectively in the global marketplace. Exxelia Microspire Microspire was founded in 1978 and became part of Exxelia Group in 2008. Exxelia Microspire has been designing, developing and manufacturing wound components for over 35 years: transformers and inductors, electro-magnets, rotors and stators. Exxelia Microspire has several manufacturing sites, notably newly located low production cost facilities offering competitive solutions. Exxelia Microspire’s know-how includes standard winding technologies: linear (in RM, ETD, EP, EFD, ER, EQ and other formats) and toroid. For harsh environment applications with shock, vibration, and high temperature issues, Microspire offers innovative specific technologies including SESI, TT and CCM. Exxelia Microspire’s qualified technologies, clearly defined design rules and industrial organization provide the platform on which it is able to offer its customers optimal solutions. Exxelia N'Ergy Exxelia N’Ergy (ex N’Ergy) was acquired in 2015 by Exxelia Group. Exxelia N’Ergy designs and manufactures passive specific electromagnetic components in small and medium range: Transformers, Chokes, Sensors (tachometer, gyros, …), Electromagnets.